| G-код: | Модаль-
ность: |
Номер группы: | Функция: |
| G00 | + | 01 | Positioning (rapid traverse) Позиционирование (ускоренное перемещение) |
| G01 | + | 01 | Linear interpolation (cutting feed) Линейная интерполяция |
| G02 | 01 | Circular interpolation CW or helical interpolation CW | |
| G03 | 01 | Circular interpolation CCW or helical interpolation CCW | |
| G04 | 00 | Dwell, Exact stop | |
| G05.1 | 00 | AI advanced preview control / AI contour control | |
| G05.4 | 00 | HRV3 on/off | |
| G07.1 (G107) | 00 | Cylindrical interpolation | |
| G09 | 00 | Exact stop | |
| G10 | 00 | Programmable data input | |
| G11 | 00 | Programmable data input mode cancel | |
| G15 | + | 17 | Polar coordinates command cancel |
| G16 | 17 | Polar coordinates command | |
| G17 | + | 02 | XpYp plane selection / Xp: X axis or its parallel axis Выбор плоскости XpYp |
| G18 | + | 02 | ZpXp plane selection / Yp: Y axis or its parallel axis |
| G19 | + | 02 | YpZp plane selection / Zp: Z axis or its parallel axis |
| G20 | 06 | Input in inch | |
| G21 | 06 | Input in mm
Единица измерения в мм. |
|
| G22 | + | 04 | Stored stroke check function on |
| G23 | 04 | Stored stroke check function off | |
| G27 | 00 | Reference position return check | |
| G28 | 00 | Automatic return to reference position | |
| G29 | 00 | Movement from reference position | |
| G30 | 00 | 2nd, 3rd and 4th reference position return | |
| G31 | 00 | Skip function | |
| G33 | 01 | Threading | |
| G37 | 00 | Automatic tool length measurement | |
| G39 | 00 | Cutter compensation : corner circular interpolation | |
| G40 | 07 | Cutter compensation : cancel | |
| G41 | 07 | Cutter compensation : left | |
| G42 | 07 | Cutter compensation : right | |
| G40.1 | 19 | Normal direction control cancel mode | |
| G41.1 | 19 | Normal direction control on : left | |
| G42.1 | 19 | Normal direction control on : right | |
| G43 | 08 | Tool length compensation + | |
| G44 | 08 | Tool length compensation - | |
| G45 | 00 | Tool offset : increase | |
| G46 | 00 | Tool offset : decrease | |
| G47 | 00 | Tool offset : double increase | |
| G48 | 00 | Tool offset : double decrease | |
| G49 | + | 08 | Tool length compensation cancel |
| G50 | + | 11 | Scaling cancel |
| G51 | 11 | Scaling | |
| G50.1 | + | 22 | Programmable mirror image cancel |
| G51.1 | 22 | Programmable mirror image | |
| G52 | 00 | Local coordinate system setting | |
| G53 | 00 | Machine coordinate system setting | |
| G54 | + | 14 | Workpiece coordinate system 1 selection |
| G54.1 | 14 | Additional workpiece coordinate system selection | |
| G55 | 14 | Workpiece coordinate system 2 selection | |
| G56 | 14 | Workpiece coordinate system 3 selection | |
| G57 | 14 | Workpiece coordinate system 4 selection | |
| G58 | 14 | Workpiece coordinate system 5 selection | |
| G59 | 14 | Workpiece coordinate system 6 selection | |
| G60 | 00 | Single direction positioning | |
| G61 | 15 | Exact stop mode | |
| G62 | 15 | Automatic corner override | |
| G63 | 15 | Tapping mode | |
| G64 | + | 15 | Cutting mode |
| G65 | 00 | Macro call | |
| G66 | 12 | Macro modal call | |
| G67 | + | 12 | Macro modal call cancel |
| G68 | 16 | Coordinate system rotation mode on | |
| G69 | + | 16 | Coordinate system rotation mode off |
| G73 | 09 | Peck drilling cycle | |
| G74 | 09 | Left-handed tapping cycle | |
| G75 | 01 | Plunge grinding cycle (for grinding machine) | |
| G76 | 09 | Fine boring cycle | |
| G77 | 01 | Plunge direct sizing/grinding cycle (for grinding machine) | |
| G78 | 01 | Continuous-feed surface grinding cycle (for grinding machine) | |
| G79 | 01 | Intermittent-feed surface grinding cycle (for grinding machine) | |
| G80 | + | 09 | Canned cycle cancel / Electronic gear box : synchronization cancellation |
| G80.4 | + | 34 | Electronic gear box : synchronization cancellation |
| G81.4 | 34 | Electronic gear box : synchronization start | |
| G81 | + | 09 | Drilling cycle or spot boring cycle / Electronic gear box : synchronization start |
| G82 | 09 | Drilling cycle or counter boring cycle | |
| G83 | 09 | Peck drilling cycle | |
| G84 | 09 | Tapping cycle | |
| G84.2 | 09 | Rigid tapping cycle (FS10/11 format) | |
| G84.3 | 09 | Left-handed rigid tapping cycle (FS10/11 format) | |
| G85 | 09 | Boring cycle | |
| G86 | 09 | Boring cycle | |
| G87 | 09 | Back boring cycle | |
| G88 | 09 | Boring cycle | |
| G89 | 09 | Boring cycle | |
| G90 | + | 03 | Absolute programming |
| G91 | + | 03 | Incremental programming Инкрементное (относительное) программирование |
| G91.1 | 00 | Checking the maximum incremental amount specified | |
| G92 | 00 | Setting for workpiece coordinate system or clamp at maximum spindle speed | |
| G92.1 | 00 | Workpiece coordinate system preset | |
| G93 | 05 | Inverse time feed | |
| G94 | + | 05 | Feed per minute |
| G95 | 05 | Feed per revolution | |
| G96 | 13 | Constant surface speed control | |
| G97 | + | 13 | Constant surface speed control cancel |
| G98 | + | 10 | Canned cycle : return to initial level |
| G99 | 10 | Canned cycle : return to R point level | |
| G160 | + | 20 | In-feed control cancel (for grinding machine) |
| G161 | 20 | In-feed control (for grinding machine) |
| M-код: | Функция: |
| M00 | Program stop (Non-optional) |
| M01 | Optional stop |
| M02 | End of program (no rewind) |
| M03 | Spindle rotation CW Вращение шпинделя по часовой стрелке |
| M04 | Spindle rotation CCW
Вращение шпинделя против часовой стрелки |
| M05 | Spindle stop
Остановка вращения шпинделя |
| M06 | Tool change
Цикл смены инструмента |
| M07 | Mist coolant ON |
| M08 | Flood coolant ON
Включение эмульсии (охлаждающей жидкости) |
| M09 | Coolant OFF
Выключение эмульсии (охлаждающей жидкости) |
| M10 | Pallet clamp ON |
| M11 | Pallet clamp OFF |
| M19 | Spindle orientation ON |
| M21 | Tool magazine right |
| M22 | tool magazine left |
| M23 | tool magazine up |
| M24 | tool magazine down |
| M25 | Tool clamp |
| M26 | tool unclamp |
| M27 | Clutch neutral ON |
| M28 | Clutch neutral OFF |
| M30 | End program (rewind stop) Полное завершение программы |
| M48 | Enable speed and feed overrides |
| M49 | Disable speed and feed overrides |
| M60 | Pallet shuttle and program stop |
| M98 | Call sub-program (subroatines) |
| M99 | End sub-program (subroatines) |
| Функция: | Объяснение: |
| Обнуление станка | |
| Работа с F-кодами | |
| Ошибка перемещения (недопустимая координата) |
Switch The Language
